← All projects

CASE 01 / Precast concrete

YFSG400 butt welding machine control retrofit

An independent OWEN PLC210 control system for a butt welding machine, integrating the automatic cycle, operator HMI, hydraulics, pneumatics and welding.

Project stageCompleted
Personal contribution

Machine survey, architecture, electrical design, PLC and HMI, installation oversight and commissioning

Technologies
OWEN PLC210-13-CSCODESYS / FBD / STOWEN SP307-RBUST3MK210-312MU210-502
Archived automatic-mode screen in the HMI editor, 31 October 2026. The interface uses a machine illustration. Logo and addresses are redacted.
Problem

The OEM control software was unavailable, making the original control system difficult to restore.

Solution

Independent OWEN controls with manual operation, an automatic cycle, an operator panel and process interlocks.

Outcome

The machine was handed over for operation after commissioning.

How resistance butt welding works

A demonstration model created for an engineering portfolio. The interface and visualization were created for this site and do not reproduce the production operator interface. Parameters and timing are illustrative.

Welding cellStandby
  • 3 Left weld carriage
  • 7 Right weld carriage
  • 4 Cutter air cylinder
  • 5 Flash cutter
  • 11 Roller
  • 13 Feed unit
  • 14 Feed carriage

Cutter profile, grips and travel are illustrative. The role of the feed carriage is being clarified.

Select a component in the illustration or the list.

Weld zone

Both workpieces share one axis. The right carriage brings the ends together. Heating and upsetting form flash around the joint.

Original problem

The YFSG400 butt welding machine used a Chinese OEM control system. Its controller source code was unavailable, which made restoring the original system difficult. The machine sequence had to be reconstructed from the installed sensors, actuators and welding equipment.

Project objective

Design and deploy an independent control system on OWEN hardware. It needed to support manual operation, an automatic welding cycle, coordinated hydraulic and pneumatic motion, welding control, process interlocks and operator diagnostics.

Reverse engineering and architecture

I surveyed the original electrical system, actuators, sensors and process sequence. I used that survey to define the I/O and allocate functions across the controller, I/O modules and operator panel. I selected the hardware and drew the electrical schematics.

The CODESYS project separates input processing, operating-mode logic and output commands. Dedicated function blocks handle the automatic cycle and the return to the initial position. This makes it possible to trace a sensor signal through the transition conditions to the actuator command.

Equipment

Function Equipment Application
Controller OWEN PLC210-13-CS Operating modes, automatic cycle and process interlocks
I/O OWEN MK210-312 and MU210-502 Discrete circuits and analogue command output
Operator interface OWEN SP307-R Controls, states, messages and settings
Hydraulics Heng Xing proportional valve and discrete directional valves Motion and switching of hydraulic mechanisms
Pneumatics Pneumatic actuators Execution of process commands
Feedback and switching Inductive sensors and electromagnetic contactors Position feedback and circuit switching
Welding subsystem BUST3 thyristor controller and welding transformer Thyristor control and power for the welding circuit

Operating modes, hydraulics and welding

I implemented manual operation and the automatic sequence in CODESYS. Transitions use mechanism positions, process delays, equipment states and interlocks. A dedicated sequence returns the mechanisms to their initial positions.

I developed the motion control logic for the Heng Xing proportional hydraulic valve, which has a ±10 V analogue interface. Discrete valves and pneumatic actuators operate within the same PLC sequence. Welding control is coordinated with the relevant stages of that sequence.

Operator interface

I developed SP307-R screens for manual and automatic modes, status monitoring, diagnostics and process settings. The panel displays the operating mode, cycle progress and equipment status messages.

Personal contribution and commissioning

I carried out the survey, designed the architecture and electrical schematics, selected hardware, programmed the PLC, developed the HMI and integrated the hydraulic, pneumatic and welding subsystems.

I organized the electrical installation and provided technical oversight to the assigned installers. I checked equipment connections and signals, configured the system and carried out commissioning.

Outcome

An independent control system for the YFSG400 butt welding machine was developed and implemented on an OWEN PLC210. After commissioning, the machine was handed over for operation.

Development records

Four redacted archive screenshots show the CODESYS project tree, an automatic-cycle excerpt and two HMI editor screens. The captions give the capture dates. The project outcome records the subsequent handover.

← All projects